🌽 Grain Gate with Chute for IBC Totes & Feed Bins – Lift-to-Pour, 9×9 in Opening
🌽 Grain Gate with Chute for IBC Totes & Feed Bins – Lift-to-Pour, 9×9 in Opening
BUNDLE & SAVE
Couldn't load pickup availability
🌽 Grain Gate with Chute for IBC Totes & Feed Bins – Lift-to-Pour, 9×9 in Opening
If you’re still scooping feed out of a tote, you’re working too hard.
Bulk feed is the smart buy. Getting it back out is the hard part.
- You lean over a 4‑foot tote with a coffee can, fishing for the corn at the bottom.
- The tote’s little drain valve won’t pass corn or pellets, so it’s no help.
- Every bucket you fill spills a little, and the mice find it before you do.
- You’ve thought about rigging a gate from sheet metal or plywood. Then the weekend fills up.
Lift the handle. Fill the bucket. That’s the whole job.
This steel gate bolts low on the front of your IBC tote, feed bin or hopper. Lift the U-handle and the plate slides up. Gravity pushes feed out through the 9 × 9 in opening and down the chute, straight into your bucket.
No reaching over the top. No scooping. Your back will feel the difference by the end of the first week.
Buy feed by the tote, not by the bag.
Bulk feed usually costs less per pound than bagged feed, and some feed mills will fill a tote for you. The catch has always been getting it back out. With a gate at the bottom, a whole tote of feed comes out one easy bucket at a time.
One handle sets the flow.
- Lift it all the way
- A full stream fills a 5‑gallon bucket fast.
- Lift it halfway
- A slow, steady trickle for topping off.
- Press it down
- The plate drops and the feed stays put.
The U-handle works like a lever, so one hand does the job. No yanking on a stuck slide.
Feed lands in the bucket, not on the floor.
A plain gate throws feed straight out, and some of it always misses. The included chute catches the flow and guides it down into the bucket. Less waste, less sweeping, and nothing left on the floor to draw mice and rats.
| Plain slide gate | This gate | |
|---|---|---|
| Chute | Not included | Included |
| Opens with | A pull tab | A lever handle |
| Mounting hardware | Varies | For totes, steel and wood bins |
| Wrenches | Not included | Hex key and wrench |
Built like farm hardware, not a gadget.
- Steel frame and plate with a rust-resistant red finish.
- Bolted pivots on every moving joint, so you can snug them up over the years.
- 6 mounting holes that bolt it flat to totes, bins and hoppers.
- 2.76 in chute walls that keep feed on course.
Check the fit in ten seconds.
It fits standard 9 × 9 in openings. All you need is a flat spot at least 10.5 in wide and 13 in tall near the bottom of your tote or bin.
- Opening
- 9 × 9 in
- Frame
- 10.5 × 13 in
- Chute width
- 8.6 in
- Depth, frame to chute tip
- 7.9 in
- Chute wall height
- 2.76 in
- Mounting
- 6 holes
- Material
- Steel, rust-resistant finish
- Works on
- IBC totes, feed bins, hoppers, wooden bins
Four steps, a drill and a jigsaw.
- MarkOutline the 9 × 9 in opening and the 6 bolt holes.
- CutDrill the holes, then saw out the opening.
- Bolt onFasten the gate with the included hardware.
- Add the chuteAttach it below the gate. Fill the tote and pour.
On an IBC tote, first trim any cage bar that crosses the gate. On a steel bin, use a metal-cutting blade.
Works with the feed you already buy.
Whether you’re filling deer feeders before the season or feeding a flock every morning, it handles shelled corn, layer pellets, whole oats, goat and livestock pellets, range cubes and seed.
Rule of thumb: if it’s dry and flows freely, it pours. Sticky sweet feed with heavy molasses and fine mash can bridge in any gravity bin, so pellets and whole grain flow best.
Everything’s in the box.
- Grain gate with lever handle
- Discharge chute
- 6 bolts, nuts and washers for totes and steel bins
- 6 wood screws for wooden bins
- Hex key and open-end wrench
- Instructions
Before you order
Will it fit my tote or bin?
If you have a flat area at least 10.5 in wide and 13 in tall near the bottom, yes. It fits standard 9 × 9 in openings on IBC totes, steel feed bins, hoppers and wooden bins. On an IBC tote, mount it at the bottom of the front wall and trim any cage bar that crosses it.
What tools do I need?
A drill, a jigsaw, a marker and a square. If you’re cutting a steel bin, fit the jigsaw with a metal-cutting blade. The bolts, nuts, washers, wood screws and both wrenches are in the box.
Which feeds work best?
Anything dry and free-flowing: shelled corn, pellets, cubes, whole oats, soybeans and most seed. Sticky sweet feed with heavy molasses and fine mash can bridge in any gravity bin and may need a tap to keep moving.
Will it empty the whole tote?
Gravity does most of the work. A flat-bottomed tote always keeps a little feed in the corners, so when it runs low, tip the tote slightly or rake the rest toward the gate.
Can the tote sit outside?
Yes. The steel has a rust-resistant finish. For an outdoor tote, run a bead of exterior silicone around the frame when you mount it, and keep the tote out of direct summer sun so the feed stays dry. Start with a food-grade tote that never held chemicals.
What if it doesn’t suit my setup?
You have 30 days to send it back. Our Refund Policy has the details, and you can message us any time.
It’s 5 a.m., it’s 12 degrees, and every animal on the place is hungry.
Lift the handle, fill the bucket and get back inside while the coffee’s still hot. Tomorrow, do it again. No scooping, no spills, no sore back.
Back to top to order
