🏍️ Self-Adjusting Motorcycle & Bike Cup Holder
🏍️ Self-Adjusting Motorcycle & Bike Cup Holder
BUNDLE & SAVE
Couldn't load pickup availability
🏍️ Self-Adjusting Motorcycle & Bike Cup Holder
Self-adjusting handlebar cup holder
Push your drink in.
It grips. Ride on.
Cans, water bottles and lidded to-go cups from 1.4" to 2.9" wide. The arms close around the drink you push in, so it rides on your bars, not at the bottom of a saddlebag.
-
1.4"–
2.9" drink width -
7/8"–
1-1/4" bar size - 360°swivel
Why riders end up skipping the drink
Buried in the bag
Every stop turns into unzip, dig, repack. So the water stays put, often on the long, hot days you need it most.
One-size cup rings
A fixed ring is sized for one container. Slim cans rattle around in it, and wider bottles won’t go in at all.
No spot for coffee or cans
Bottle cages are built for cycling bottles. Many e-bikes and scooters don’t even have a place to mount one.
MENDTIDE fixes all three. It clamps to the bar, and its arms close around the drink you push in.
How it works
-
1
Clamp it on
Tighten the clamp on any round bar from 7/8" to 1-1/4" (22–32 mm). No drilling, nothing permanent.
-
2
Push your drink in
Pressing it down into the cage closes the arms around it, from a slim can to a 2.9" bottle.
-
3
Grab it at the stop
Lift it straight out with one hand, and push it back in when you’re done.
One holder for the can, the bottle and the coffee
A fixed ring fits one size. These arms close in until they meet the container, so a slim energy drink sits as snug as a 16.9 oz water bottle.
- Holds containers 1.4"–2.9" (36–74 mm) wide
- Cans, water bottles, sports bottles and lidded to-go cups
- Supported from below, gripped from the sides
- Reinforced nylon frame with metal arms
Upright on any bar angle
The cage turns a full 360° on its clamp. Stand it straight on a flat or sloped bar, then angle it to where your hand naturally lands at a stop.
- Stands upright on flat or sloped bars
- Turns toward your hand for an easy grab
- Easy to keep clear of levers, switches and mirrors
If it’s a round tube from 7/8" to 1-1/4", it’s a mount
On a motorcycle, that means the handlebar, the engine guard or a passenger grab rail. It also clamps to e-bike and scooter bars, where a frame battery takes the bottle cage’s spot or there’s no cage mount at all.
- Motorcycles
- E-bikes
- Bicycles
- Scooters
- ATVs
- Boat rails
Check the fit in one minute
Two numbers decide it: how wide your drink is and how thick your bar is.
Your drink
1.4"–2.9"36–74 mm- 2.1"Slim energy-drink can
- 2.6"12 oz soda can or 16.9 oz water bottle
- 3"+Big tumblers and wide-mouth flasks won’t fit
Your bar
7/8"–1-1/4"22–32 mm- 7/8"Most motorcycle handlebars, many bicycles and scooters
- 1"Common on cruisers and touring bikes
- 1-1/4"Many engine guards and passenger rails
Not sure? Wrap a strip of paper around the bar, mark where it overlaps, then divide that length by 3.14.
On the bar in a few minutes
-
Pick the spot
A straight, round section of tube, clear of levers, switches and mirrors.
-
Clamp it
Tighten until the holder won’t slip or turn with a full drink in it. Snug is enough on carbon or thin-wall bars.
-
Set the angle
Swivel the cage upright and toward your hand.
-
Check full lock
Turn the bars lock to lock. Nothing should touch the tank, fairing or cables. Recheck the clamp after rough roads.
Questions riders ask
Will my drink fit?
If it’s 1.4"–2.9" (36–74 mm) wide, yes: soda and energy-drink cans, 16.9 oz water bottles, sports bottles up to 2.9" and lidded to-go cups. Big tumblers and wide-mouth flasks are too wide.
Will it fit my handlebar?
It clamps round tubes from 0.87" to 1.26" (22–32 mm), which covers 7/8", 1", 1-1/8" and 1-1/4" bars. Clip-on sport bars rarely have room to spare, so check clearance in your riding position first.
Can it hold a hot coffee?
Yes, as long as the part of the cup that sits in the holder is 2.9" or narrower. Keep the lid on while you’re moving.
Will it rattle or let go on rough roads?
The base supports the drink while the arms grip it from the sides, so it can’t slide around the way it does in a loose ring. Off-road or on washboard, use a closed container and recheck the clamp from time to time.
Can I move it to another bike, a stroller or a boat?
Yes. It’s clamp-on, so there’s no drilling and nothing permanent. Loosen the screw and move it to any round tube from 22 to 32 mm.
Will it stop every spill?
No holder can promise that. An open cup can still slosh over bumps, so use a lidded or closed container.
Ride safe. Mount it where it can’t touch the brake or clutch lever, throttle, switches or tank at full lock. On a motorcycle, reach for your drink only when you’re stopped.
Bring the drink. Keep the bag zipped.
Self-adjusting grip, 360° swivel and a clamp for 7/8"–1-1/4" bars. Buying it as a gift? Most motorcycle handlebars are 7/8" or 1", and both fit.
Get yours
